The Channel Recorder supports the following containers and codecs.

Note: If a combination of CODEC / CONTAINER / RESOLUTION is not supported, Channel Recorder floods the logs with errors. If this happens stop the recording using RECORD STOP. Please make sure that the mentioned combination are supported by consulting the tables below.

Note: Only the containers AVCINTRAMXF, DVCPROMXF, XDCAMMXF, XAVCMXF support capturing of closed captions. The closed captions must be part of SMPTE 334M CDP. The captured close caption is found in the recorded clip in the wrapper according to SMPTE 436M and in the actual MXF essence.

Note: The examples below are not exhaustive. Some parameters such as the number of audio channels have other options.

PAL Codecs

MPEG-IFrame

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.avi

MPEG2-IFrame422

720x576

Alpha: No
Bitrate: 10-50
Bit depth: 8
VBI: N/A
Timecode: N/A
TDIR: Yes

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC IFrame
CONFIG SET CONTAINER AVI
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

DVCAM

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.avi	DV/DVCAM 4:2:0 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCam` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mov	DVCAM 4:2:0 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCam` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DVCAM 4:2:0 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC DvCam` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

Information: Video bitrate is 25, but the encoded bitrate is 28.75 (15% more) which includes other data.

DVCPRO

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.avi	DVCPRO 4:1:1 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.avi	DVCPRO 50 4:2:2 720x576	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mov	DVCPRO 4:1:1 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mov	DVCPRO 50 4:2:2 720x576	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf (OP1a)	DVCPRO 4:1:1 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER DVCPROMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "dvcpro" SET U1 MED vtr.media.mpeg.bit_rate "25000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf (OP1a)	DVCPRO 50 4:2:2 720x576	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER DVCPROMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "dvcpro" SET U1 MED vtr.media.mpeg.bit_rate "50000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf Panasonic P2 (OP-Atom)	DVCPRO 4:1:1 720x576	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MXF` RECORD CLIP clip `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mxf Panasonic P2 (OP-Atom)	DVCPRO 50 4:2:2 720x576	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type

Information: Video bitrate is 25, but the encoded bitrate is 28.75 (15% more) which includes other data. The same applies for 50 bitrate. The encoded bitrate is 57.6 (15% more).

XDCAM

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf XDCAM (OP1a)

D10 (IMX50) 4:2:2
720x608

Alpha: No
Bitrate: 50
Bit depth: 10
VBI: required
Timecode: required
TDIR: Yes
CC: Yes

AES3:

4ch: 24 in 32-bit; 48kHz
8ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 50
CONFIG SET AUDIOCHANNELS 4
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2"

SET U1 MED vtr.media.mpeg.bit_rate "50000000"

SET U1 MED vtr.media.audio.input.channels "4"

CUER U1

REC U1

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf XDCAM (OP1a)

D10 (IMX40) 4:2:2
720x608

Alpha: No
Bitrate: 40
Bit depth: 10
VBI: required
Timecode: required
TDIR: Yes
CC: Yes

AES3:

4ch: 24 in 32-bit; 48kHz
8ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 40
CONFIG SET AUDIOCHANNELS 4
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2"

SET U1 MED vtr.media.mpeg.bit_rate "40000000"

SET U1 MED vtr.media.audio.input.channels "4"

CUER U1

REC U1

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf XDCAM (OP1a)

D10 (IMX30) 4:2:2
720x608

Alpha: No
Bitrate: 40
Bit depth: 10
VBI: required
Timecode: required
TDIR: Yes
CC: Yes

AES3:

4ch: 24 in 32-bit; 48kHz
8ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 40
CONFIG SET AUDIOCHANNELS 4
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2"

SET U1 MED vtr.media.mpeg.bit_rate "30000000"

SET U1 MED vtr.media.audio.input.channels "4"

CUER U1

REC U1

NTSC Codecs

MPEG IFrame

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.avi

MPEG2-IFrame422

720x480

Alpha: No
Bitrate: 10-50
Bit depth: 8
VBI: N/A
Timecode: N/A
TDIR: Yes
CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC IFrame
CONFIG SET CONTAINER AVI
CONFIG SET BITRATE 50
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type

DVCAM

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.avi	DV/DVCAM 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCam` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mov	DVCAM 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCam` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mxf Panasonic P2 (OP-Atom)	DVCAM 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: N/A CC: No	No Audio	`CONFIG SET CODEC DvCam` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type

Information: Video bitrate is 25, but the encoded bitrate is 28.75 (15% more) which includes other data.

DVCPRO

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.avi	DVCPRO 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.avi	DVCPRO 50 4:2:2 720x480	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mov	DVCPRO 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mov	DVCPRO 50 4:2:2 720x480	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mxf (OP1a)	DVCPRO 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER DVCPROMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "dvcpro" SET U1 MED vtr.media.mpeg.bit_rate "25000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf (OP1a)	DVCPRO 50 4:2:2 720x480	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER DVCPROMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "dvcpro" SET U1 MED vtr.media.mpeg.bit_rate "50000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf Panasonic P2 (OP-Atom)	DVCPRO 4:1:1 720x480	Alpha: No Bitrate: 25 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type
.mxf Panasonic P2 (OP-Atom)	DVCPRO 50 4:2:2 720x480	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC Dv50` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type

Information: Video bitrate is 25, but the encoded bitrate is 28.75 (15% more) which includes other data. The same applies for 50 bitrate. The encoded bitrate is 57.6 (15% more).

XDCAM

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf XDCAM (OP1a)

D10 (IMX50) 4:2:2

720x512

Alpha: No
Bitrate: 50
Bit depth: 10
VBI: Required
Timecode: Required
TDIR: Yes
CC: Yes

AES3:

4 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 50
CONFIG SET AUDIOCHANNELS 4
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2"

SET U1 MED vtr.media.mpeg.bit_rate "50000000"

SET U1 MED vtr.media.audio.input.channels "4"

CUER U1

REC U1

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf XDCAM (OP1a)

D10 (IMX40) 4:2:2

720x512

Alpha: No
Bitrate: 40
Bit depth: 10
VBI: Required
Timecode: Required
TDIR: Yes
CC: Yes

AES3:

4 ch: 24 in 32-bit; 48kHz
8ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 40
CONFIG SET AUDIOCHANNELS 4
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2"

SET U1 MED vtr.media.mpeg.bit_rate "40000000"

SET U1 MED vtr.media.audio.input.channels "4"

CUER U1

REC U1

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf XDCAM (OP1a)

D10 (IMX30) 4:2:2

720x512

Alpha: No
Bitrate: 30
Bit depth: 10
VBI: Required
Timecode: Required
TDIR: Yes
CC: Yes

AES3:

4 ch: 24 in 32-bit; 48kHz
8ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 30
CONFIG SET AUDIOCHANNELS 4
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2"

SET U1 MED vtr.media.mpeg.bit_rate "30000000"

SET U1 MED vtr.media.audio.input.channels "4"

CUER U1

REC U1

720p50 and 720p59.94 (60M) Codecs

MPEG-IFrame

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.avi

MPEG2-IFrame422

1280x720

Alpha: No
Bitrate: 50-300
Bit depth: 8
VBI: N/A
Timecode: N/A
TDIR: Yes
CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC IFrame
CONFIG SET CONTAINER AVI
CONFIG SET BITRATE 50
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

DVCPRO HD

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.avi	DVCPRO HD 1280x720	Alpha: No Bitrate: 100-115 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mov	DVCPRO HD 960x720	Alpha: No Bitrate: 100-115 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf (OP1a)	DVCPRO HD 960x720	Alpha: No Bitrate: 100-115 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER DVCPROMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "dvcpro" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf Panasonic P2 (OP-Atom)	DVCPRO HD 960x720	Alpha: No Bitrate: 100-115 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XDCAM HD 422

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM HD 422

1280x720

Alpha: No
Bitrate: 50
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2-ibp-422p@hl"

SET U1 MED vtr.media.audio.input.channels "8"

CUER U1

REC U1

XDCAM EX HQ

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM EX HQ

1280x720

Alpha: No
Bitrate: 35
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 16 in 16-bit; 48kHz
4 ch: 16 in 16-bit; 48kHz
8 ch: 16 in 16-bit; 48kHz
16 ch: 16 in 16-bit; 48kHz

CONFIG SET CODEC XDCamEX
CONFIG SET CONTAINER XDCAMMXF
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

AVC-Intra

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.mxf (OP1a)	AVCIntra Class 50 960x720	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC AVCIntra50` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET BITRATE 50` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "avc-intra" SET U1 MED vtr.media.mpeg.bit_rate "50000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf (OP1a)	AVCIntra Class 100 1280x720	Alpha: No Bitrate: 100 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC AVCIntra100` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET BITRATE 100` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "avc-intra" SET U1 MED vtr.media.mpeg.bit_rate "100000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf Panasonic P2 (OP-Atom)	AVCIntra Class 50 960x720	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC AVCIntra50` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET BITRATE 50` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	AVCIntra Class 100 1280x720	Alpha: No Bitrate: 100 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC:No	No Audio	`CONFIG SET CODEC AVCIntra100` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET BITRATE 100` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

ProRes

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mov

I-Frame 4:2:2

1280x720

Alpha: No
Bitrate: 100 (LT), 147, 220 (HQ)
Bit depth: 10
VBI: N/A
Timecode: N/A
TDIR: Yes, with .ref file
CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC ProRes
CONFIG SET CONTAINER MOV
CONFIG SET BITRATE 100
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

DNxHD

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.mxf (OP1a)	DNxHD (50) 120, 175 DNxHD (59.94) 145, 220 1280x720	Alpha: No Bitrate (50): 120,175 Bitrate (59.94): 145,220 Bit depth: 8 VBI: N/A Timecode: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER DNXHDMXF` `CONFIG SET BITRATE 120` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf (OP1a)	DNxHD (50) 175x DNxHD (59.94) 220x 1280x720	Alpha: No Bitrate (50): 175x Bitrate (59.94): 220x Bit depth: 10 VBI: N/A Timecode: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER DNXHDMXF` `CONFIG SET BITRATE 175` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DNxHD (50) 120, 175 DNxHD (59.94) 145, 220 1280x720	Alpha: No Bitrate (50): 120,175 Bitrate (59.94): 145,220 Bit depth: 8 VBI: N/A Timecode: N/A CC: No	No Audio	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 120` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DNxHD (50) 175x DNxHD (59.94) 220x 1280x720	Alpha: No Bitrate (50): 175x Bitrate (59.94): 220x Bit depth: 10 VBI: N/A Timecode: N/A CC: No	No Audio	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 175` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XAVC

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XAVC

Alpha: No
Bitrate: 100
Bit depth: 10
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

PCM:

16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XAVC
CONFIG SET CONTAINER XAVCMXF
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

Note: The configuration v210 must be enabled in the configuration section for recording XAVC.

1080i25 and 1080i29.97 (30M) Codecs

MPEG-IFrame

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.avi

MPEG2-IFrame422

1920x1080

Alpha: No
Bitrate: 50-300
Bit depth: 8
VBI: N/A
Timecode: N/A
TDIR: Yes
CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC IFrame
CONFIG SET CONTAINER AVI
CONFIG SET BITRATE 50
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

DVCPRO HD

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.avi	DVCPRO HD (25) 1920x1080 DVCPRO HD (29.97) 1260x1080	Alpha: No Bitrate: 100 Bit depth: 8 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER AVI` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mov	DVCPRO HD (25) 1920x1080 DVCPRO HD (29.97) 1260x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MOV` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DVCPRO HD (25) 1920x1080 DVCPRO HD (29.97) 1260x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER MXF` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf (OP1a)	DVCPRO HD (25) 1920x1080 DVCPRO HD (29.97) 1260x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 4 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DvCPro` `CONFIG SET CONTAINER DVCPROMXF` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "dvcpro" SET U1 MED vtr.media.mpeg.bit_rate "100000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1

Information: Video bitrate is 100, but the encoded bitrate is 115 (15% more) which includes other data.

XDCAM HD 422

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM HD 422

1920x1080

Alpha: No
Bitrate: 50
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XDCam
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

UADD CS_ENCODER1 * SHAR dart

SET U1 MED vtr.media.video.input.compression.type "mpeg2-ibp-422p@hl"

SET U1 MED vtr.media.audio.input.channels "8"

CUER U1

REC U1

XDCAM HD LP

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM HD LP

1440x1080

Alpha: No
Bitrate: 17.5
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 16 in 16-bit; 48kHz
4 ch: 16 in 16-bit; 48kHz
8 ch: 16 in 16-bit; 48kHz
16 ch: 16 in 16-bit; 48kHz

CONFIG SET CODEC XDCamHD
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 18
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XDCAM HD SP

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM HD SP

1440x1080

Alpha: No
Bitrate: 25
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 16 in 16-bit; 48kHz
4 ch: 16 in 16-bit; 48kHz
8 ch: 16 in 16-bit; 48kHz
16 ch: 16 in 16-bit; 48kHz

CONFIG SET CODEC XDCamHD
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 25
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XDCAM HD HQ

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM HD HQ

1440x1080

Alpha: No
Bitrate: 35
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 16 in 16-bit; 48kHz
4 ch: 16 in 16-bit; 48kHz
8 ch: 16 in 16-bit; 48kHz
16 ch: 16 in 16-bit; 48kHz

CONFIG SET CODEC XDCamHD
CONFIG SET CONTAINER XDCAMMXF
CONFIG SET BITRATE 35
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XDCAM EX HQ

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XDCAM EX HQ

1920x1080

Alpha: No
Bitrate: 35
Bit depth: 8
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

No Audio

PCM:

2 ch: 16 in 16-bit; 48kHz
4 ch: 16 in 16-bit; 48kHz
8 ch: 16 in 16-bit; 48kHz
16 ch: 16 in 16-bit; 48kHz

CONFIG SET CODEC XDCamEX
CONFIG SET CONTAINER XDCAMMXF
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

AVC-Intra

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.mxf (OP1a)	AVCIntra Class 50 1440x1080	Alpha: No Bitrate: 50 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC AVCIntra50` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET BITRATE 50` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "avc-intra" SET U1 MED vtr.media.mpeg.bit_rate "50000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf (OP1a)	AVCIntra Class 100 1920x1080	Alpha: No Bitrate: 100 Bit depth: 8 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC AVCIntra100` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET BITRATE 100` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "avc-intra" SET U1 MED vtr.media.mpeg.bit_rate "100000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf Panasonic P2 (OP-Atom)	AVCIntra Class 50 1440x1080	Alpha: No Bitrate: 50 Bit depth: 10 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC AVCIntra50` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 50` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	AVCIntra Class 100 1920x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC AVCIntra100` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 100` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

ProRes

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mov

I-Frame 4:2:2

1920x1080

Alpha: No
Bitrate: 100 (LT), 147, 220 (HQ)
Bit depth: 10
VBI: N/A
Timecode: N/A
TDIR: Yes, with .ref file
CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC ProRes
CONFIG SET CONTAINER MOV
CONFIG SET BITRATE 100
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

DNxHD

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.mxf (OP1a)	DNxHD (30) 120, 185 DNxHD (29.97) 145, 220 1920x1080	Alpha: No Bitrate (50): 120,185 Bitrate (59.94): 145,220 Bit depth: 8 VBI: N/A Timecode: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER DNXHDMXF` `CONFIG SET BITRATE 120` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf (OP1a)	DNxHD (30) 185x DNxHD (29.97) 220x 1920x1080	Alpha: No Bitrate (50): 185x Bitrate (59.94): 220x Bit depth: 10 VBI: N/A Timecode: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER DNXHDMXF` `CONFIG SET BITRATE 185` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DNxHD (30) 120, 185 DNxHD (29.97) 145, 220 1920x1080	Alpha: No Bitrate (50): 120,185 Bitrate (59.94): 145,220 Bit depth: 8 VBI: N/A Timecode: N/A CC: No	No Audio	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 120` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DNxHD (30) 185x DNxHD (29.97) 220x 1920x1080	Alpha: No Bitrate (50): 185x Bitrate (59.94): 220x Bit depth: 10 VBI: N/A Timecode: N/A CC: No	No Audio	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 185` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XAVC

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XAVC

Alpha: No
Bitrate: 100
Bit depth: 10
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

PCM:

16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XAVC
CONFIG SET CONTAINER XAVCMXF
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

Note: The configuration v210 must be enabled in the configuration section for recording XAVC.

1080p50 and 1080p59.94 (60M) Codecs

AVC-Intra

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.mxf (OP1a)	AVCIntra Class 50 1440x1080	Alpha: No Bitrate: 50 Bit depth: 10 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC AVCIntra50` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "avc-intra" SET U1 MED vtr.media.mpeg.bit_rate "50000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf (OP1a)	AVCIntra Class 100 1920x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: Yes TDIR: Yes CC: Yes	PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC AVCIntra100` `CONFIG SET CONTAINER AVCINTRAMXF` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	UADD CS_ENCODER1 * SHAR dart SET U1 MED vtr.media.video.input.compression.type "avc-intra" SET U1 MED vtr.media.mpeg.bit_rate "100000000" SET U1 MED vtr.media.audio.input.channels "8" CUER U1 REC U1
.mxf Panasonic P2 (OP-Atom)	AVCIntra Class 50 1440x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC AVCIntra50` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 50` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	AVCIntra Class 100 1920x1080	Alpha: No Bitrate: 100 Bit depth: 10 VBI: N/A Timecode: N/A TDIR: Yes CC: No	No Audio	`CONFIG SET CODEC AVCIntra100` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 100` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

MPEG-IFrame

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.avi

MPEG2-IFrame422

1920x1080

Alpha: No

Bitrate: 50-300

Bit depth: 8

VBI: N/A

Timecode: N/A

TDIR: Yes

CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC IFrame
CONFIG SET CONTAINER AVI
CONFIG SET BITRATE 50
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

ProRes

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mov

I-Frame 4:2:2

1920x1080

Alpha: No
Bitrate: 100 (LT), 147, 220 (HQ)
Bit depth: 8, 10
VBI: N/A
Timecode: N/A
TDIR: Yes, with .ref file
CC: No

No Audio

PCM:

2 ch: 24 in 32-bit; 48kHz
4 ch: 24 in 32-bit; 48kHz
8 ch: 24 in 32-bit; 48kHz
16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC ProRes
CONFIG SET CONTAINER MOV
CONFIG SET AUDIOCHANNELS 8
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

DNxHD

Container	Codec	Features	Audio	VizSend Example	MVCP Example
.mxf (OP1a)	DNxHD (50) 240, 365 DNxHD (59.94) 290, 440 1920x1080	Alpha: No Bitrate (50): 240, 365 Bitrate (59.94): 290, 440 Bit depth: 8 VBI: N/A Timecode: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER DNXHDMXF` `CONFIG SET BITRATE 240` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf (OP1a)	DNxHD (50) 365x DNxHD (59.94) 440x 1920x1080	Alpha: No Bitrate (50): 365 x Bitrate (59.94): 440x Bit depth: 10 VBI: N/A Timecode: N/A CC: No	No Audio PCM: 2 ch: 24 in 32-bit; 48kHz 4 ch: 24 in 32-bit; 48kHz 8 ch: 24 in 32-bit; 48kHz 16 ch: 24 in 32-bit; 48kHz	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER DNXHDMXF` `CONFIG SET BITRATE 365` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DNxHD (50) 240, 365 DNxHD (59.94) 290, 440 1920x1080	Alpha: No Bitrate (50): 240 , 365 Bitrate (59.94): 290 , 440 Bit depth: 8 VBI: N/A Timecode: N/A CC: No	No Audio	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 240` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.
.mxf Panasonic P2 (OP-Atom)	DNxHD (50) 365x DNxHD (59.94) 440x 1920x1080	Alpha: No Bitrate (50): 365 x Bitrate (59.94): 440x Bit depth: 10 VBI: N/A Timecode: N/A CC: No	No Audio	`CONFIG SET CODEC DNxHD` `CONFIG SET CONTAINER MXF` `CONFIG SET BITRATE 365` `CONFIG SET AUDIOCHANNELS 8` `RECORD CLIP clip` `RECORD START`	Specifying this codec / container combination is not supported through MVCP. If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

XAVC

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XAVC

Alpha: No
Bitrate: 100
Bit depth: 10
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

PCM:

16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XAVC
CONFIG SET CONTAINER XAVCMXF
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

Note: The configuration v210 must be enabled in the configuration section for recording XAVC.

2160p50 and 2160p59.94 (60M) Codecs

XAVC

Container

Codec

Features

Audio

VizSend Example

MVCP Example

.mxf (OP1a)

XAVC

Alpha: No
Bitrate: 300, 480, (VBR/CBR)
Bit depth: 10
VBI: N/A
Timecode: Yes
TDIR: Yes
CC: Yes

PCM:

16 ch: 24 in 32-bit; 48kHz

CONFIG SET CODEC XAVC
CONFIG SET CONTAINER XAVCMXF
CONFIG SET BITRATE 300
RECORD CLIP clip
RECORD START

Specifying this codec / container combination is not supported through MVCP.

If this codec / container combination is required then the web interface can be used to configure Channel Recorder. When sending MVCP commands, however, the codec / container must not be specified via vtr.media.video.input.compression.type.

Note: A M264 board is recommended for recording UHD.

Note: The configuration uhd and v210 must be enabled in the configuration section for recording UHD.